technical data sheet cable stripper for portable electric drill 60W010-C06 rosenberger hochfrequenztechnik gmbh & co. kg tel.: +49 8684 18-0 page p.o.box 1260 d-84526 tittmoning germany fax: +49 8684 18-499 www.rosenberger.de email: info@rosenberger.de 1 / 2 rf_35/12.04/3.0 suitable cables 1 1/4" annular corrugated cable flexline 1 1/4 r (recommended) packing standard 1 pce in box weight 670 g/pce replacement blades 1 pcs type pj-2: 60w010-c05/50 1 pcs type pj-3: 60W010-C06/50 1 pcs type pj-222: 60W010-C06/51 draft date approved date rev. engineering change nu mber name date rong fang 05/07/05 gramsamer 22/07/05 a00 04-0130 r ong fang 05/07/05 w hile the information has been carefully compiled to the best of our knowledge, nothing is intended as representation or warranty on our part and no statement herein shall be construed as recommendation to infringe existing patents. in the effort to improve our products, we reserve the right to make changes judg ed to be necessary.
technical data sheet cable stripper for portable electric drill 60W010-C06 rosenberger hochfrequenztechnik gmbh & co. kg tel.: +49 8684 18-0 page p.o.box 1260 d-84526 tittmoning germany fax: +49 8684 18-499 www.rosenberger.de email: info@rosenberger.de 2 / 2 rf_35/12.04/3.0 application feature the cable preparation tool automates the preparatio n of corrugated coaxial cables. a locating system, comprised of spring-loaded steel balls, controls th e preparation dimensions of the cable jacket, outer conductor, foam and inner conductor. the tool is us ed for the assembly of the following connectors on a flexline? 1 1/4 r cable with annular corrugation. connector order no.: 53s115-c06n1, 53k115-c06n1 60s115-c06n1, 60k115-c06n1 important tool tips and instructions 1. always wear safety glasses and protective gloves and dont insert the finger into the tool. 2. to cut the cable use a hacksaw or use cable cutt ers in a rocking motion to maintain the cylindrical shape of the cable. 3. ensure that at least 20 cm (8) of the cable is straight before using the tool. 4. the use of a cordless drill is recommended (3/8 14.4v minimum / 1/2"18v recommended), operate the drill in the 400-650 rpm range. 5. we recommended practicing this procedure on scra p cable to get the feel for the spring-loaded ball bearing locating system that controls the cab le preparation dimensions. 6. insert the tool on the cable and operate the dri ll in a fluid clockwise direction with slight forwa rd pressure. 7. as the spring-loaded ball bearings pass over the crest of the corrugation, you will feel resistance from the springs and from the blades as they cut t he cable. when the ball bearings fall into the first valley you will hear the pith of the drill m otor increase and the resistance subside. the blades have finished their cut. allow the drill to turn the tool a few extra revolutions without applying any forward pressure . this will ensure a clean and uniform preparation. 8. periodically mist the blades with wd-40 or simil ar lubricant and clean the tool body. this will increase blades life significantly. 9. follow additional instructions that are provided with each connector. while the information has been carefully compiled t o the best of our knowledge, nothing is in tended as representation or warranty on our part and no statement herein shall be construed as recommendation to infringe existing patents. in the effort to improve our products, we reserve the right to make changes judg ed to be necessary.
|
